VELIMAX

Appears New

VELIMAX Rain Glass Window Film is designed to give a beautiful appearance of rain patterned glass to your windows and doors, whether for some privacy, to block out an unsightly view or for decorative purposes. Besides prevent UV rays, it can also cut out a large proportion of the unwanted glare, whilst still allowing natural light to pass through. It will work on any smooth glass surface and can be used anywhere in the home, requires no additional cleaning and can be installed at a fraction of the cost. VELIMAX Rain Glass Window Films SPECIFICATIONS: Material: Vinyl Environmental: Through Europe EN71-3 standard and SGS Appearance Type: 3D Installation Type: Static Cling Thickness: 0.29mm (excluding the backing film) Average life: 3 years PACKAGE INCLUDED: 1 Roll Window Film1 Instructions for installation Get the Rain Glass Look with VELIMAX Rain Glass Window Film! Static Cling The rain glass window film is made out of a durable vinyl material which is scratch and tear resistant. There is no adhesive gel material involved which means no sticky or messy residue is left behind on the surface The static window clings can be applied to a smooth, clean, and non porous surface. It’s ideal for rented properties or for temporary privacy requirements. UV Protection Our window film blocks up to 97% of UV (ultraviolet) rays from getting into your home. The decorative glass film can protect your floors, window treatments, artwork, furnishings, and store merchandise from fading and damaging. The privacy window film works as a shield for UV rays. It still allows natural light in but blocks ultraviolet rays out. Read more Wide Range of Applications - Suitable for a smooth, clean, and non porous surface. Frequently Asked Questions: 1. How to deal with the air bubbles? Use a hard plastique squeegee or any plastic card to squeegee air bubbles and water. If you find it's hard to get rid of the bubbles, uncover the window film, spray more water between the glass and the film and squeegee firmly again. Water will make it much easier to remove bubbles. 2. Why the film fall off after a while? Please check if you have removed the liner, trimmed the edges or squeegeed excess water and bubbles. Leave a 1/16” wide gap around the four perimeter edges of the film. This gap is essential for the proper thermal expansion of the glass and allows you to completely squeegee the water and air from under the film.The blade or the knife for cutting the film is not sharp, resulting in deformation at the edge of the film. NOTE: Film can dull a blade edge quickly; and a dull blade can tear film. 3. Can I remove the film at a later stage? Absolutely. Our blackout film is removable and reusable. You can just simply peel the film off the glass in seconds with no mess. 4. How to peel off the backing liner? All static cling films have a liner, but some are clear and hard to see at first glance. If you can’t separate the liner from the film, place a piece of scotch tape on both sides of the sheet, fold the tape over to create tabs, and use the tabs to separate the two sides. DETAILS: Non Adhesive Easy to remove, no mess, no residue. Waterproof Easy to clean. Thickening Material Give your window a fresh rain glass look. Read more HOW TO INSTALL THE WINDOW FILM? Before You Begin: Make a wetting solution. Wetting solution is the secret ingredient to a smooth, seamless installation. Make a solution by adding 8 drops of a mild, non- moisturizing dish detergent (do not use hand soap) to a 32-oz. spray bottle filled with clean water. Mix well. Make a work-space. Give yourself enough space to work. You will need enough flat surface to lay out the film for measuring, cutting, marking and prep. Work in a dust-free area. Turn off fans. STEP-BY-STEP INSTALLATION INSTRUCTIONS: Measure and record the length and width of the glass surface.Cut the film along the grid and add 1+ inch on every side when doing this so you have excess film to trim away.lean the glass surface and the frame.Peel the backing film off.Generously spray the water on the static side of the film.Lightly mist the glass.Place the film on the wet window.Use a plastic card to squeegee the water and air out under the film.Use the plastic card to work the film into the edges as tightly as possible. Trim excess material away with a sharp razor, leaving a 1/16” wide gap around the four perimeter edges of the film. We've Got Your Windows and Doors Covered. VELIMAX values every customer. If you find any defects with our window film or have questions during the installation, please message us directly, we will give you the best solution. Read more

LLXXYM90001

YEL5120855

2.0 inches

1.5 inches

1.2 pounds

35.5 inches

Appears New

7405 Industrial Road, Florence KY 41042